Automatic slack adjusters (ASAs) are a key part of keeping today’s commercial vehicle brakes operating at peak performance and up to regulatory standards. As part of its Bendix Tech Tips series, Bendix Commercial Vehicle Systems LLC stresses two key recommendations for automatic slack adjusters: keep them properly lubricated, and do not routinely manually adjust out-of-adjustment wheel-ends equipped with ASAs.

All too often, we see automatic slack adjusters that are not being greased regularly during scheduled maintenance and inspections,” said Frank Gilboy, product manager, automatic slack adjusters at Bendix Spicer Foundation Brake LLC, a joint venture between Bendix Commercial Vehicle Systems LLC and Dana Commercial Vehicle Products, LLC. “And slack adjusters that don’t perform properly through lack of lubrication can have a direct impact on both safety and regulatory compliance.”

Greasing the ASA serves two vital purposes: Forcing the new lubricant in purges the old grease from the adjuster, along with any water or contaminants that have found their way in; and it protects the adjuster’s internal gear sets, clutches, and other components from wear. Both are necessary to keep the ASA working properly to maintain correct brake stroke and provide optimal stopping performance.

Lubrication is a simple process, regardless of the adjuster’s manufacturer. Just locate the ASA’s grease fitting, attach the hose from a grease gun, and inject new grease until old grease is forced through the release opening. The release location varies depending on the maker – for the Bendix® Versajust® LS™, it’s on the boot; for others, it’s a hole in the casting – and manufacturer instructions will offer advice on how much grease to purge from the adjuster, and what lubricant to use.

It should easily take less than a minute per adjuster,” Gilboy said. “Bendix recommends greasing with an NGLI grade-2 lubricant every 30,000 miles, but you can also make things less complicated by greasing the ASAs every time you do a preventive maintenance inspection.”

Because properly installed, operating, and lubricated automatic slack adjusters should never need adjusting after the initial setup, aside from brake relining, Bendix also emphasizes that an out-of-adjustment ASA should never simply be manually adjusted to correct an out-of adjustment brake stroke.

Gilboy noted that while there are many factors that can cause an ASA to be out of adjustment, it is likely that none of these will be remedied with a manual adjustment.

We continue to hear stories of technicians or vehicle owners who believe that it’s acceptable to routinely adjust automatic slacks,” continued Gilboy. “This may be a holdover from the days of manual slacks, but it’s simply not acceptable for ASAs. Manual adjustment may seem to temporarily solve the out-of-adjustment issue, but there may be other factors at play that must be addressed – otherwise the condition will reoccur. As always, it’s critical to maintain, adjust, or replace slack adjusters according to the manufacturer’s instructions.”

Bendix typically recommends measuring the chamber stroke on each wheel-end by checking the distance from the chamber to the pin with the brakes released, and again after a full brake application. The difference between the two measurements is the chamber stroke. The maximum allowable stroke under CVSA guidelines is based on the chamber size and type.

To determine whether a slack adjuster is properly adjusting the brake, refer to the manufacturer’s instructions and mechanism tests. (For example, the Bendix Versajust slack adjuster test is described on page 6 of the product Service Data Sheet.)

Once the ASA itself has been inspected, use the following checklist to examine other wheel-end components and fix any situations that can lead to overstroke. Where component replacement is necessary, Bendix stresses the use of OEM-equivalent equipment to ensure correct operation and best performance.

  • Check for proper lubrication of the brake camshaft and cam tube.
  • Inspect the cam head and rollers for abnormal wear.
  • Evaluate the brake’s friction blocks for wear level and cracks, replacing the friction if necessary.
  • Inspect the camshaft bushings for wear by checking radial and axial endplay, following the brake manufacturer’s guidelines. If necessary, replace the bushings.
  • Check the brake drums for maximum diameter and surface finish, and replace if necessary.
  • Check the brake shoe return springs to ensure a proper return to the “zero stroke” position.
  • Inspect the return spring on the air chamber or on the service side of double diaphragm spring brakes.
  • Inspect the clevis pins connecting the chamber to the automatic slack adjuster to ensure they turn freely and are coated with an anti-seize lubricant.

Upon completing these inspections, verify the slack adjuster’s performance by following the manufacturer’s instructions on conducting a functional check. If the slack adjuster is still not functioning according to the manufacturer’s recommendations, replace per TMC RP609.

The correct brake stroke is absolutely crucial to braking performance and safe vehicle operation, so it plays an important role in roadway safety,” Gilboy said. “Today’s automatic slack adjusters, kept in good working condition and regularly greased, help brake systems perform to their engineered specifications, leading to safer trucks and safer highways for everyone.”

Information in the Bendix Tech Tips series, along with instructional videos and interactive training, can also be found at the Bendix On-Line Brake School, For more information on automatic slack adjusters, reference the Bendix SD-05- 4630, in the Document Library on

Download Tech Tip

Tech Tips

Technical advice on the topics that matter most.

Replacing An Air Disc Brake Caliper? Here's What You Need to Know.

What to do if it’s time to replace an ADB caliper and how you can protect your investment in the technology.

Read More

Antilock Braking Systems (ABS): Troubleshooting and Repair

ABS plays an important role in driver and vehicle safety. This Tech Tip discusses what to do if you discover an illuminated ABS warning lamp.

Read More

Protecting Wheel-Ends in Off-Highway and Severe Duty Applications

Construction site haulers, cement trucks, and other haulers face increased risks of contamination and corrosion.

Read More